San Michele Arcangelo, Borgo di Terzo Building

San Michele Arcangelo Borgo di Terzo, Bergamo Church, Design

San Michele Arcangelo, Italy : Borgo di Terzo Building

Bergamo Church Building – Restoration of Historic Italian Architecture

9 Jul 2012

The Church of St. Michael the Archangel, Borgo di Terzo

Location: near Bergamo, north eastern Italy

3D documentation in the restoration of historic buildings

Structural changes to historic buildings depend on the precise recording of existing conditions – an ideal application for modern 3D laser scanners.

Korntal-Münchingen, July 2012 – The church of St. Michael the Archangel (1735) stands in the centre of Borgo di Terzo, near Bergamo, Italy. Cracks were clearly visible in the front elevation masonry, indicating serious building damage. Due to its irregular architecture, the church – like all historic buildings – required a precise analysis of existing conditions as a basis for the renovation work.

San Michele Arcangelo Borgo di Terzo Bergamo Church Building Church of St. Michael the Archangel Borgo di Terzo Bergamo Church Building San Michele Arcangelo Borgo di Terzo Bergamo Church Building Church of St. Michael the Archangel Borgo di Terzo Bergamo Building

Exact measurements are enormously important, especially with structural intervention, and they form the foundation for structural analysis using the finite element method (FEM). 3D laser scanning is superb for the accurate recording of existing conditions. Comprehensive spatial data that can be used for structural analysis with standard software solutions is quickly and easily available. At the same time, all data is available for CAD design of the restoration. Compared with classic measurement methods, laser scanning is more accurate and efficient. The equipment is easy to operate and enables 360° data capture. Laser scanning provides records in which every individual point shows the same accuracy in the spatial coordinate system. Thus, it is possible to use the generated cloud of individual points (point cloud) not only for the investigation of a building component – as would be the case in measurement with a total station – but also to automatically record structural deformations of additional building components at the same time.

As a basis for the forthcoming structural improvements to the church in Borgo di Terzo, the engineering faculty of Bergamo University made use of a FARO laser scanner and was able to record the interior of the building in a single day. A graphical approach was chosen to filter and interpolate the scanning data for the detailed investigations that followed before the renovation. This enabled use of normal architectural procedures for the building analysis: for example, systematic investigation of crack patterns in the masonry to display the damage in the orthogonal projection or a comparison of the actual geometry of a vault deformed under its own weight with its ideal geometry.

San Michele Arcangelo Borgo di Terzo Bergamo Church Building Church of St. Michael the Archangel Borgo di Terzo Bergamo Church Building San Michele Arcangelo Borgo di Terzo Bergamo Church Building Church of St. Michael the Archangel Borgo di Terzo Bergamo Building

In order to be able to use the church scan data with FEM, the point cloud had to be converted from a continuous model to a numerical model. Subsequently, sections relevant to the damage investigation and orthogonal to each other could be selected. Here, element grids with a uniform spacing of 30 x 30 x 30 cm proved to be a good compromise in representing significant parts of the building structure.

In the course of 3D documentation with the FARO laser scanner, the cause of the observed damage became clear: The timber roof framework had settled as a result of earlier restoration. Both a tie anchor and upper spines resting on the vault were affected. This led to heavy deflection and severe damage to the underlying vault masonry.

The current load distribution in the vault was evaluated and distribution following the planned restoration was checked, using FEM analysis. It showed that both the arched buttress supports and the corresponding anchors required renovation. In addition, the middle arch must be reinforced with a steel grid and lime mortar. The deformation of the vault under load also showed that a tie member of the vault spine had given way, suggesting replacement of this anchor. After these reinforcement measures were incorporated into the FEM model of existing conditions, a general improvement in the entire structural condition became apparent.

San Michele Arcangelo Borgo di Terzo Bergamo Church Building Church of St. Michael the Archangel Borgo di Terzo Bergamo Church Building San Michele Arcangelo Borgo di Terzo Bergamo Church Building Church of St. Michael the Archangel Borgo di Terzo Bergamo Building

Church of St. Michael the Archangel, Borgo di Terzo, images / information received Jul 2012

Churches

Location: Borgo di Terzo, Italy, southern Europe

Italian Architecture Designs

Contemporary Italian Architectural Selection

Italian Architectural Designs – chronological list

Italian Architectural News

Milan Architecture Tours

Another Italian Church building on e-architect:

Church Complex Pescara, eastern Italy
Architetto Angelo Campo
Church Complex Pescara

Facade of Basilica San Petronio – Wall as a Center, Bologna, Emilia Romagna, north-central Italy
Design: Inter-Esse Studio
Facade of Basilica San Petronio in Bologna
image © IES
Basilica San Petronio, Bologna

Complesso Parrocchiale S Paolo, Foligno, Umbria
Design: Massimiliano Fuksas, Doriana Fuksas / Massimiliano Fuksas Architecture
San Paolo Parish Complex Foligno
photograph : Moreno Maggi
San Paolo Parish Complex of Foligno Building

Bergamo Buildings

Church Buildings

Italian Architecture

Italian Buildings

Italian Houses

Italian Architect

Comments / photos for the San Michele Arcangelo – Borgo di Terzo church page welcome